the Otherpower.com Discussion Board || Wrong Motor

Front Page - [Homebrewed Electricity-- (wind) (solar) (hydro) (steam) (controls) (storage) (mechanical)] - Classifieds - Site News
Everything - Newbies - [Remote Living-- (housing) (heat) (light) (water)] - Rants & Opinion - Diaries - Our Products

Wrong Motor
By adaml, Section Wind Posted on Mon Aug 25th, 2008 at 12:25:08 PM MST
Wind Motor

I have attached a dc 130v 2 1/2hp permanent magnet generator to my blades. They seem to spin at a good rate but I am not managing to get more than 3v produced. Being new to all of this please could someone tell me if I have made a fundamental error and am trying to use the wrong type of motor?
Many thank,
Adam.

Wrong Motor | 56 comments (56 topical, 0 editorial)

Re: Wrong Motor (3.00 / 0) (#1)
by Norm (peppysue@suite224.net) on Mon Aug 25th, 2008 at 06:53:32 AM MST
(User Info)

Need Much More Data ......
How big are your blades? What rpm does the motor
spin to make 130 volts?
We have no way of knowing 5000 rpm?
Seem to spin at a good rate?
M'Gosh ...I have some pinwheels out in my yard
that are spinning at a good rate..
(not being sarcastic just giving you an example)
If you have a motor that will give you about 3 or
4 volts cranking it by hand at 60 rpm then you
might have the right motor.......
( :>) Norm

( :>) Norm

Re: Wrong Motor (3.00 / 0) (#2)
by Norm (peppysue@suite224.net) on Mon Aug 25th, 2008 at 06:56:54 AM MST
(User Info)

3 or 4 open volts, that is
( :>) Norm
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#4)
by adaml on Mon Aug 25th, 2008 at 07:16:49 AM MST
(User Info)

That is 3volts with no load, just connected to multimeter.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#3)
by adaml on Mon Aug 25th, 2008 at 07:04:10 AM MST
(User Info)

Thanks Norm,
Apologies new to all this but should have provided better info.
Blades are 36", 3 of made of 6" pvc piping I had lying about, mounted on an 8" aluminium hub.
I reckon that in today's wind (which is the strongest I have tested in yet) I am getting about 200 - 300 rpm max. I do not reckon this is enough even though the blades are spinning to fast to visually keep up with sometimes.
When I initially got the motor I did rig it up, a spin with my fingers was enough to make a 12v car light bulb glow. Spinning it up on my drill at maximum rev's turned out about 80v.
I am trying to build this as a prototype for a friend who wants to set it up on a remote piece of land.
The tower is approx 12"
My apologies again for the original scant infromation.
Many thanks for you help.
Adam.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#5)
by Norm (peppysue@suite224.net) on Mon Aug 25th, 2008 at 07:33:54 AM MST
(User Info)

You're new....so first of all got nothing to do
for awhile.....so.....

First off your picture is a link or something
have you followed Wooferhounds instructions on
how to post pictures....It was just posted recently
so you should have no trouble finding it.

I got your picture , but it was a roundabout
way of getting it...not convenient don't worry...
we all had trouble posting pictures when we
started.

I don't think there is anything wrong with the
motor....just your connections maybe...are you
connected to a battery when you measure this
voltage?

Had one person get varying voltage....turned out
the hub was slipping on the shaft.....not good !
LOL

( :>) Norm

Re: Wrong Motor (3.00 / 0) (#6)
by CmeBREW (smke833f@hotmail.com) on Mon Aug 25th, 2008 at 07:50:40 AM MST
(User Info)

What is the rpm of the motor? If it is 6700rpm , then it is no good as a mill generator. It would take over 600rpm to reach the 12 volt cut-in with a 4' diameter prop. What is the diameter of your prop and type of blades?

Re: Wrong Motor (3.00 / 0) (#9)
by adaml on Mon Aug 25th, 2008 at 12:31:54 PM MST
(User Info)

I very obviously have a great deal to learn, lol, thank you all for your input. The motor is rated at 95-130 VDC, 0-6750 rpm which I got the net, hence wondering if it is not the best one for the job. The wind here is not clean but I intend to set it up to test properly in a large open field next door away from all buildings, trees etc. However, I had hoped to see more than max 3v when only connected to my multimeter.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#12)
by kurt on Mon Aug 25th, 2008 at 01:36:51 PM MST
(User Info)

you would have to spin that motor approximately 625 rpm or so to get 12v out of it that is way to fast for a windmill always look for a low rpm motor when looking at motors the crazy fast ones don't put out anything at a speed you can spin them with a prop. to get a general idea how fast you are going to have to spin a motor to get the cut in voltage you want divide the max rpm on the nameplate by the max voltage on the nameplate then multiply that number by your cut in voltage. usually 12 for small systems. that will give you a ballpark idea if the motor will work or not. 4' props like to cut in about 300-350 rpm the larger the prop the slower the cut in needs to be

http://www.reresource.org/

IRC
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#13)
by adaml on Mon Aug 25th, 2008 at 02:15:12 PM MST
(User Info)

Thanks Kurt,

Hmmmm, should have done a bit more in-depth research before rushing to purchase a motor, just trusted the description given on the web site! My blades are 36" length each, three of and I do not think that they will ever realistically spin to 625rpm. This size seemed larger than others had made having done a trawl of others websites.
Is there a golden rule or some basic figures to look for when chosing a motor? Think I might have to go back to the drawing board regarding the motor and call that lesson learnt. I have heard of Ametek motors but again they seem to come in all shapes and sizes so am a bit ignorant of which sort is best suited.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#15)
by Norm (peppysue@suite224.net) on Mon Aug 25th, 2008 at 06:44:00 PM MST
(User Info)

An Ametek motor is perhaps your best bet for
beginning...Here is a very good link....
http://www.tlgwindpower.com/ametek.htm
and get a load of that TLG 500 watt generator !
Nice huh?
BTW...looks like you're handy enough to make
your own Alternator ...have you ever considered
making your own from an old 20" window box fan?
makes about 50 watts uses much smaller blades
half the size of your blades....most difficult
is grinding 4 flats on the armature and gluing
4 neo magnets onto it.
Ghurd posted in his diary awhile back....

( :>) Norm
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#7)
by TomW on Mon Aug 25th, 2008 at 08:08:56 AM MST
(User Info)

adam;

Well, it looks nice but in that location it will be unlikely to get much clear wind. You cannot really judge that turbine's performance in that setting.

Surrounded by tall "stuff". Even if it is open land behind the photographer the turbulence would rob all the power the wind might have.

Be much easier for you to get useful test data by spinning it with a rope around the axle, a drill or something in bench type tests.

What feels like a nice strong breeze will not be the same as an open field breeze due to turbulence from air hitting all that stuff around the turbine.

The turbine looks nice. I suggest you haul it out in the country someplace open and set it up you might be surprised at how quick it might spin up in open air wind.

Don't get discouraged, I had the same problem with a couple turbine experiments in close to the buildings here and I am in a very rural area.

Tom

"Education consists mainly of what we have unlearned."--Mark Twain

Re: Wrong Motor (3.00 / 0) (#8)
by tanner0441 on Mon Aug 25th, 2008 at 08:28:08 AM MST
(User Info)

I could not understand why I seemed to have a good wind where I am. Then I bought an anemometer from EBay, my good wind, which was blowing plants over, turned out to be about 3 to 5 mph and swirling.

just a thought

Brian

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#10)
by adaml on Mon Aug 25th, 2008 at 12:36:15 PM MST
(User Info)

Thank you Tom, was beginning to get a bit discouraged must admit, will persevere though! I did test the motor by connecting to my drill and it produced plenty of voltage, up to about 80 but this was obviously spinning very fast!! The motor itself is dc with four leads from it. As far as I can determine there is only one positive and one negative output, I can not fathom what the other two leads are for.
Again thank you.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#11)
by TomW on Mon Aug 25th, 2008 at 01:25:23 PM MST
(User Info)

adam;

I can not fathom what the other two leads are for

It could be some form of feedback. maybe a hall sensor or ?? Slap an ohmmeter on it see if it gets a reaction when spun?

Lots of motors use feedback schemes for positioning, limits, etc.

Good luck with it.

Tom

"Education consists mainly of what we have unlearned."--Mark Twain
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#14)
by jlt on Mon Aug 25th, 2008 at 03:34:55 PM MST
(User Info)

I took a look at your picture. And i think most of your problem is in the blades.

Re: Wrong Motor (3.00 / 0) (#17)
by adaml on Tue Aug 26th, 2008 at 05:56:25 AM MST
(User Info)

Thanks again all for all your feedback. Jlt please could I ask what you reckon the problem is with the blades?

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#18)
by ghurd on Tue Aug 26th, 2008 at 07:26:53 AM MST
(User Info)

Far too steep at the root to go very fast.
http://www.fieldlines.com/story/2003/11/11/172721/53
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#19)
by adaml on Tue Aug 26th, 2008 at 09:05:50 AM MST
(User Info)

Thanks ghurd, please could you put that in layman's (or idiots) terms!!!!! I am guessing that means I need to cut some off the blades near the hub?? I should have posted in the newbie section, I now realise!!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#21)
by ghurd on Tue Aug 26th, 2008 at 09:54:40 AM MST
(User Info)

About half as wide near the hub.
Quick guess: measuring around the curve near the hub should be about 2.5" or 2- 5/8".

The far blade in the pic looks strange at the hub.
The near and highest blade looks like the tip may be twisted backwards, and that will get worse as pressure from the wind increases, slowing the blades down. The tip should be angled the same direction as the root (hub area).

The diameter will have to be smaller too. Maybe 42" is what I would try, for no other reason than a gut feeling.

The hub looks OK, but I'm not too picky about that.

Don't expect much until the leaves fall, and the location still won't be very good.

I don't think all hope is lost. I am sort of surprized it made 3V like it is.
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#22)
by adaml on Tue Aug 26th, 2008 at 10:13:13 AM MST
(User Info)

Thanks ghurd, so I need to shave some of the blade width off near the hub and reduce blade length/overall diameter? All I did to make these blades, as a first attempt, was to 1/4 6" pipe, use masking tape as a stencil and cut along that, hadn't done much other tampering with the design!! I didn't know what to expect when first hooked up to multimeter but when whipping round got just over 3v unloaded. I suppose I am looking for maximum speed for the area, as you say not the ideal location.
Supposed to be working but fascinating info on here, thanks to all, and for all the continued help.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#23)
by ghurd on Tue Aug 26th, 2008 at 10:53:21 AM MST
(User Info)

Yes, shorter, narrower blades.

And it wasn't whipping around. It was crawling by our collective standards.
Wait until you see it with better blades!
Scared the poo out of me the first few times.

CmeBREW has a pic that will give you an idea of how it should end up.
His are tweaked for his purpose, but notice the root area where it meets the hub.
His have a curve after that, which isn't needed.
Also notice the tip of the far blade, and its angle.
Best pic I could recall.
http://www.otherpower.com/images/scimages/3274/leesonpvcblades2.jpg

G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#24)
by adaml on Tue Aug 26th, 2008 at 11:32:00 AM MST
(User Info)

Thanks very much ghurd and LOL, obviously still snails pace then, enough to split my nose open when I walked into it trying to get the cat in!!
I have another rough cut set of blades 24" in length each. I will try to narrow these off and attach them and see what happens, would you reckon that is an acceptable length or do you suggest shortening to 21"? Thanks for the continued help.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#27)
by CmeBREW (smke833f@hotmail.com) on Tue Aug 26th, 2008 at 02:04:09 PM MST
(User Info)

This is in response to the PVC blades link that Ghurd showed. I hope scoop puts it in the right place-- sometimes it goes to the very bottom of the thread.

That link to the pvc blades were my first version. I trimmed them down thinner to make them go faster here:

However, the diameter of these blades is 6ft. 10 inches.
The 12v cut-in for the big DC motor I used for this prop was only 130rpm--- which is Much, MUCH slower than his 620rpm (12v) cut-in dc motor.
Even though these blades are quite fast (not as fast as wood though) , they would be nowhere near fast enough for that motor the poster has.

I think he needs to get a better dc motor with a lower 12v cut-in.
Also , I think the cogging is significant with his motor and very difficult to start up with a 4' diameter prop even with 5 thin pvc blades.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#28)
by ghurd on Tue Aug 26th, 2008 at 03:09:09 PM MST
(User Info)

I do know what you mean, but the perspective in the photo you posted makes them look like spaggetti!
I tried to show him the end view. His end view of the root looks like nearly 90 degrees. Your photo shows the end view of a decent PVC blade very well.

The motor could be better.
I am trying to get something from what is available, before he gives up.
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#29)
by CmeBREW (smke833f@hotmail.com) on Tue Aug 26th, 2008 at 05:24:10 PM MST
(User Info)

Ghurd-
Yeah, it is difficult to see the perspectives clearly with photos. You are right, the one you showed shows the angles better for a perpective. I just thought I would say that by making them even thinner (less wide) it did clearly get more speed which is what he needs a lot of.

I could not see his photo of his mill anywhere. How are all of you seeing his photo??

I even went to his 'files' to try to find it, but no photo!
No one ever said if his blades are pvc or wood?? I suppose pvc.

I also hope he don't get discouraged. I remember the frustration of only reaching 10 volts (so close, yet SOO far away!) in a fairly big wind with motors similar to that one.
Maybe Flux's high speed blade design can get over that cogging well enough and make the extra speed needed. Worth a try.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#31)
by wooferhound (tim((NoSpamAt))wooferhound.com) on Wed Aug 27th, 2008 at 05:46:18 AM MST
(User Info) http://wooferhound.com

Here are his pictures . . .
http://www.otherpower.com/images/scimages/11306/

W o o f -={(

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#30)
by adaml on Wed Aug 27th, 2008 at 02:57:28 AM MST
(User Info)

Hi Ghurd, many, many thanks again, and to you all, would be easy to get dispondent at this stage! I have tried to post two new pics, following norms instructions. One of the blades mounted on a test hub and another of a smaller blade I was tinkering with last night. Your continued input would be very much appreciated. Also have been looking at a Ametek 30vdc on Ebay but getting expensive!!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#32)
by ghurd on Wed Aug 27th, 2008 at 06:57:26 AM MST
(User Info)

The new blade looks a lot better.

The blades on the test hub are far too wide at the root. Looking at them straight from the front, part of the back of the blade is visable. That is simply way too wide to work much at all.

Another look at the 1st photo makes me wonder how close the blades match.
The better they match, the faster it will turn with a load.

The 80V with the drill turning it... What is the name plate RPM of the drill?
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#33)
by adaml on Wed Aug 27th, 2008 at 08:27:49 AM MST
(User Info)

Thanks Ghurd and for the continued encouragement. I will have to look at the drill rpm when I get home tonight. Probably quite high as its a decent Bosch I brought to punch hole through the wall of the house!
I had offered the blades up to each other and weighed each as best I could. I know the match was not 100% but was reasonably happy with it. I had not balanced yet either.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#34)
by adaml on Thu Aug 28th, 2008 at 03:29:18 AM MST
(User Info)

Ghurd, I have followed your advice and shortened and narrowed the blades, have posted pic of them up. I would be most grateful for your thoughts. They certainly look a lot better to me!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#35)
by ghurd on Thu Aug 28th, 2008 at 07:29:13 AM MST
(User Info)

Much better!
Still not a great motor, and the blades are probably not a good match to the motor (PVC blades are somewhat forgiving), but the chances of it working just went up a lot.

I am quite confident they will reach charging voltage.
I would expect charging to start at about 0.1875 x drill RPMs.
The 0.1875 is from the drill test (15V charging voltage / 80V tested).
But you never can tell if the motor knows the math! Many of mine do not.

I hope you learn something from it, and have fun. The next one is easier.

Great emphasis needs placed on the current site being VERY bad.
It will need to be in a spot with nothing in front or behind. Or higher.
I get nothing as soon as the trees bud in spring. Your trees look more dense than mine.
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#37)
by adaml on Thu Aug 28th, 2008 at 09:42:53 AM MST
(User Info)

Hi Ghurd, Thanks so much for your continued support. I have ordered a totally different motor, my calculations should give approx 12v at 180rpm in 5-10mph winds, has been shipped so getting excited! Found an old post on here where someone else had brought the same motor as this and gave up, someone else posted they were no good....you live and learn and is all fun! This turbine is to go on top of a hill on an island in the Adriatic so hopefully lots of sea breezes. For mine I will go a lot higher to clear as much wind interference as possible.
Will also try to reshape my old larger blades for a bit more experimentation. The small ones went last night in a breeze with a push to get them going so I think I am also suffering with this "no good" motor from cogging, if that is the correct term?! Thanks again Ghurd, wish I had found this forum long ago!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#36)
by TomW on Thu Aug 28th, 2008 at 08:05:28 AM MST
(User Info)

adam;

I realize you are in "testing mode" but I have to mention that dangling cable is very likely to get caught in the prop if you don't secure it from flopping around as a big loop. Had it happen myself on a test stand it made a mess and ripped the cable and brushes right out of the Ametek I was testing. I didn't see it happen but the postmortem indicated it had yawed hard and the loop opened and did not follow fast enough and the blade hooked in the loop and the rest was simply physics.

You are coming along nicely. Getting rid of that curl at the root should help it speed wise.

Tom

"Education consists mainly of what we have unlearned."--Mark Twain
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#38)
by adaml on Thu Aug 28th, 2008 at 09:45:34 AM MST
(User Info)

Thanks Tom, will get rid of that loop tonight, that was laziness on my part, no excuses!!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#43)
by adaml on Mon Sep 1st, 2008 at 07:08:18 AM MST
(User Info)

Thanks again all. Have adapted blade and speed is a lot better, never thought it would go that fast!! Can I ask what is probably a really fundamental and beginners question about load and its definition. I am getting about 24v plus "unloaded" which I define as nothing bar multimeter connected. The thing I have noted is that with the motor connected to even just the three core wire down the tower that there is far more physical resistance coming from the motor. Connected to a bulb for example then this is even greater. This is what I understand to be "load". Am I correct in this line of thinking? Many thanks and apologies for sounding like and idiot!!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#44)
by ghurd on Mon Sep 1st, 2008 at 08:54:56 AM MST
(User Info)

I knew it would work. :-)

There should be no extra drag with just more wire. Check for one wire touching another.

The bulb is a load, but it is almost a short as far as the windmill is concerned. Bulbs are not much good for testing a windmill.

When charging a battery, no current will flow until the windmill voltage is higher than the battery voltage + diode voltage. No current flow means unloaded.

There should be no current flowing before about 7MPH wind, or it will "stall" trying to make power that is not available in the amount of wind.
Things will improve when the battery is connected.

You understand you need a blocking diode?
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#45)
by adaml on Mon Sep 1st, 2008 at 09:02:52 AM MST
(User Info)

Thank again Ghurd, you have been great support and encouragement. Will check the wires tonight when get home but don't think any touching. Have taken the three from the motor, connected to 7 meters 3 core down the inside of the tower then to rectifier. Connected to a battery would be a load also? I tested just by connecting my multimeter to the output with nothing else connected (pic on file), so unloaded. Have ordered a blocking diode and brought an inline fuse to go between the mill and batteries. Have acquired five new car batteries, understand they are not ideal but think they will do for a start.
Also see there is a book out, will wait for pay day and pre-order!!
Thanks again. Will keep you posted. If ever there is anything I can do in return.......

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#46)
by TomW on Mon Sep 1st, 2008 at 09:17:03 AM MST
(User Info)

adam;

Careful, now. If you go praising Ghurd too much, between that all the income from his controller he will not be able to get in or out of his shop with his swollen head.

Seriously, tho, he is a great contributor here along with many others, of course.

Luckily his newfound fame and fortune have not significantly affected his humility [YET]!

Tom

"Education consists mainly of what we have unlearned."--Mark Twain
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#47)
by adaml on Mon Sep 1st, 2008 at 09:23:01 AM MST
(User Info)

LOL Tom!!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#49)
by ghurd on Tue Sep 2nd, 2008 at 07:53:18 AM MST
(User Info)

I still fit through doorways...
My ears only rub a little! :-)
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#50)
by TomW on Tue Sep 2nd, 2008 at 10:17:58 AM MST
(User Info)

M
A
N

T
h
i
s

t
h
r
e
a
d

h
a
s

g
o
t
t
e
n

n
a
r
r
o
w

"Education consists mainly of what we have unlearned."--Mark Twain
[ Parent ]

Re: Wrong Motor (3.00 / 0) (#48)
by adaml on Mon Sep 1st, 2008 at 02:02:08 PM MST
(User Info)

HI Guys and Ghurd, just to let you know took mill to friends farm and set up there, 20mph wind avg, highest reading on multimeter just over 70v unloaded so reckon heading in right direction!! Thanks again all for the help and inspiration.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#20)
by adaml on Tue Aug 26th, 2008 at 09:16:30 AM MST
(User Info)

Or the angle of the blade when attached to the hub is wrong??

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#16)
by Norm (peppysue@suite224.net) on Mon Aug 25th, 2008 at 06:58:32 PM MST
(User Info)

Here's Ghurd's motor conversion.....
http://www.fieldlines.com/story/2005/7/4/34446/17324
Looks simple enough?
( :>) Norm

Re: Wrong Motor (3.00 / 0) (#25)
by Flux on Tue Aug 26th, 2008 at 11:54:04 AM MST
(User Info)

I didn't intend to get dragged into this one, but I did wonder if your prop was 3ft or 6ft diameter, I wish we could find some way round this ambiguity.

Your motor is very fast and you would need very fast blades to stand any sort of chance with a 6ft prop. I agree with the others that your prop looks very strange indeed with far too much pitch.

If you really want to try a high speed prop then it may just be worth looking at the freelite prop. It was 2 blade and at 6ft that is not a serious disadvantage but normally I would suggest you keep to 3 blades.

The Freelite cut in at about 450 rpm and reached full power about 1100 rpm so you would loose out on the low winds but you would certainly get well above cut in in higher winds.

At least the details would give you some idea of the sort of angles you should aim for for a fast prop. This one has no twist but it would probably start with your motor. If you reduced diameter to 4ft 6" or 5ft then you may need to think about having a coarse angle near the root, but the same small angle would be fine near the tip.

I think you should be able to follow the drawing.

Flux

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#26)
by adaml on Tue Aug 26th, 2008 at 12:06:38 PM MST
(User Info)

Thanks very much Flux, diameter is 6 foot. Personally, and the more I read and the more I learn from you people, I think my motor is too fast and am looking at another with far lower rated rpm at 30vdc. I would, however, still like to up the speed of my attempt. Thanks for the diag. makes more sense now.
With regard to length and pitch, I was obviously labouring mistakenly under the impression that the larger the blade and more pitch on each blade the better they would catch and "scoop" the air thus forcing them round. Looking at the pics on this forum it seems the correct approach is to "slice" through the air? Thank you again.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#39)
by adaml on Fri Aug 29th, 2008 at 08:06:28 AM MST
(User Info)

Dear All, just a quick note to say still going, not been breath of wind to see what the modified blades will do, very frustrating. Will keep experimenting and will try to get some info together both successes and failures and pics as might be of interest to others, would like to think so anyway. Thanks again all.

Re: Wrong Motor (3.00 / 0) (#40)
by ghurd on Fri Aug 29th, 2008 at 10:13:42 AM MST
(User Info)

Newton's 4th Law states "A new windmill will not see wind for 3 days".

Not may people are aware of Newton's 4th Law. Mostly just windmill people.
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#41)
by DamonHD (d@hd.org) on Fri Aug 29th, 2008 at 10:44:27 AM MST
(User Info) http://www.earth.org.uk/

And putting up solar panels causes thunderstorms or even sunspots.

Rgds

Damon

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#42)
by adaml on Fri Aug 29th, 2008 at 02:46:45 PM MST
(User Info)

LOL fellas!!! 'Tis true not a breath of air, yet we are forecast thunderstorms over the weekend!!!! Made another set of even thinner blades, 21" in length so will see what happens if/when the wind arrives!

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#51)
by adaml on Fri Sep 5th, 2008 at 04:51:49 AM MST
(User Info)

Quick update, mill now up and flying, pic posted, any comments more than welcome, thanks again all for the invaluable input.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#52)
by ghurd on Fri Sep 5th, 2008 at 06:42:16 AM MST
(User Info)

You really trimmed those trees!
Great. Congrat's!
Now it works! But probably not perfect.

The 70V open has me a little bit concerned about "stall".
If 70V open was at 20MPH wind, then it may stall.
If 70V open was in a gust a ways past 20MPH, then I think it'll be OK.
I believe PVC blades are pretty forgiving where it comes to almost stalling.

After you get a feel for how it is working with PVC blades, may want to upgrade to Flux's blade.

The location in the recent photo is nice. PVC blades may not handle that kind of wind too well or too long.

"Stall"
http://www.fieldlines.com/story/2007/10/21/02221/609

G-

Re: Wrong Motor (3.00 / 0) (#53)
by adaml on Fri Sep 5th, 2008 at 08:55:53 AM MST
(User Info)

Hi Ghurd, would guess that the 70v open was in a gust over 20mph. Hooked up to batteries and lights as load it was sticking to an average of 30v. Don't know a lot about stalling yet but will do some reading, thanks for the link, still need to work on a control unit but am bit stuck there at present, (can you suggest a good "idiots guide"), so doing things manually. Thanks again for your help.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#54)
by ghurd on Fri Sep 5th, 2008 at 09:23:30 AM MST
(User Info)

I am SOOoo late for work.
There is some confusion with terms.
This is a 12V system, correct?
Not sure what 30V means or where it came from, or how the battery and bulbs were connected.
It should be hard to get past about 15V with a battery connected.

Valterra posted some things you may find helpfull. Stall, light bulbs, and batteries...
http://www.fieldlines.com/story/2008/3/19/04550/2068

Simple control unit? Funny you should mention that. LOL.
http://www.fieldlines.com/story/2007/8/24/172521/889
http://ghurd.info/dc.html
G-

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#56)
by adaml on Fri Sep 5th, 2008 at 09:36:10 AM MST
(User Info)

Thanks Ghurd, my confusing terminology, did exactly as Valterra did, hands on, experimental approach!! Voltage was regulated with batteries connected, switched on two 12v 20w lights wired in parallel and voltage dropped, switched off and rose again until batteries regulated. At work myself so will read the rest later. Thanks again.

[ Parent ]

Re: Wrong Motor (3.00 / 0) (#55)
by ghurd on Fri Sep 5th, 2008 at 09:34:23 AM MST
(User Info)

One more...
http://www.fieldlines.com/story/2008/6/9/41955/41967
G-

[ Parent ]

Wrong Motor | 56 comments (56 topical, 0 editorial)

Menu

� create account
� How to use the board
� FAQs
� search the board
� Google search the board
� Old Otherpower Board

Login

Make a new account

Username:

Password:

Total Views

��114 Scoop users have viewed this posting.

Related Links

� magnet
� Also by adaml

You must be a registered user to post here. It's easy and free, and the link is on the upper right side of your page.
All trademarks and copyrights on this page are owned by their respective companies. Postings are owned by the poster, but may be deleted or moved at the ADMIN's sole discretion. The Rest � 2003 Forcefield.
You can Email the board ADMIN here. PLEASE include the username you signed up with!