« previous next »
Pages: [1]   Go Down

Author Topic: washer S rotor progress  (Read 1761 times)

0 Members and 1 Guest are viewing this topic.

georgeodjungle

  • Full Member
  • ***
  • Posts: 193
washer S rotor progress
« on: September 16, 2005, 11:09:17 PM »
you get grand daughter to cut oil barrels in half





weld back together 8" off center with 3/4" pipe in center





ask your 18 year old son for the tungs off his new house





weld h frame insert bearing


get old washer insert cogs of a bike "tryed tranny and belt didn't work to good"

bad low start up.





drill holes to mount genny





sorrie i'm out of time gots to go to elko nv more postings next week.

ver 3.0 s rotor works great.

« Last Edit: September 16, 2005, 11:09:17 PM by (unknown) »
Logged

Shadow

  • Sr. Member
  • ****
  • Posts: 473
Re: washer S rotor progress
« Reply #1 on: September 16, 2005, 08:27:00 PM »
8 year old with bare arms and bare legs grinding? I hope she at least had safety glasses!
« Last Edit: September 16, 2005, 08:27:00 PM by Shadow »
Logged

nvmike

  • Newbie
  • *
  • Posts: 47
Re: washer S rotor progress
« Reply #2 on: September 16, 2005, 08:40:27 PM »
Looking forward to your progess.  Are you near Elko Nv?


I am from Winnemucca Nv and working on a few designs but nothing to report yet.

« Last Edit: September 16, 2005, 08:40:27 PM by nvmike »
Logged

Jerry

  • Hero Member
  • *****
  • Posts: 1519
Re: washer S rotor progress
« Reply #3 on: September 16, 2005, 09:50:13 PM »
Hi nvmike


My wife and I were in Winnemucca a few days back. We were on our way back from CO. on our visit with our son and DanB at OP HQ.


We had breakfast at the Red Lion and played a couple slots. My wife took some pix of the County buildings 10 comandment stones and the old Catholic church.


I think you must get good winds there on ocasion. We came back to Oregon through McDermit on 95.


The world is small hu? We'll go back that way some day?


                             JK TAS Jerry

« Last Edit: September 16, 2005, 09:50:13 PM by Jerry »
Logged

georgeodjungle

  • Full Member
  • ***
  • Posts: 193
Re: washer S rotor progress
« Reply #4 on: September 20, 2005, 04:35:08 PM »
yep glasses are a must and we weld with no gloves to.

« Last Edit: September 20, 2005, 04:35:08 PM by georgeodjungle »
Logged

georgeodjungle

  • Full Member
  • ***
  • Posts: 193
Re: washer S rotor progress
« Reply #5 on: September 20, 2005, 04:40:37 PM »
i'm in elko right now well actualy spring creek nv.

looking to buy genny from newguyand working on rentals.

i'll be going by ya on my way home in portola ca.
« Last Edit: September 20, 2005, 04:40:37 PM by georgeodjungle »
Logged

nvmike

  • Newbie
  • *
  • Posts: 47
Re: washer S rotor progress
« Reply #6 on: September 20, 2005, 04:48:30 PM »


Jerry


Not much wind here in Winnemucca Nv.  I am thinking of giving up on the wind projects and concentration on solar come Spring.  I may leave a wind project up to watch it spin now and then.  Thanks for stopping a playing a few slots, I hope you did not take many nevada nickels back to OR.  I saw a piece in the local paper a whil back that a large wind project is planned on BLM land up on highway 95, must be more wind there then here in town.  Next time you are through this way, I will buy lunch.


mike

« Last Edit: September 20, 2005, 04:48:30 PM by nvmike »
Logged

Jerry

  • Hero Member
  • *****
  • Posts: 1519
Re: washer S rotor progress
« Reply #7 on: September 21, 2005, 12:07:43 AM »
OK great Mike. I'll tell my wife Mike,s buyin us steak & Lobster. LOL just kidin. MIKY Ds is good enough for me.


Thanks for the invite.


                         JK TAS Jerry

« Last Edit: September 21, 2005, 12:07:43 AM by Jerry »
Logged
Pages: [1]   Go Up
« previous next »