Author Topic: one side one 240v inverter  (Read 1698 times)

0 Members and 1 Guest are viewing this topic.

georgeodjungle

  • Full Member
  • ***
  • Posts: 193
one side one 240v inverter
« on: June 06, 2005, 03:50:53 AM »
any body know if you could hookup a 240 volt inverer to the main panel.

like a amis-3000-240 to run the hole house & get 240 to run a dryer & welder..

seems like the load would have to be balanced on the inverter.

but it's not on the grid.

would you have to put it in some thing like a transformer with a center tap.

or just use a 120v and jump them?

after cutting off the grid.

« Last Edit: June 06, 2005, 03:50:53 AM by (unknown) »

domwild

  • Sr. Member
  • ****
  • Posts: 357
Re: one side one 240v inverter
« Reply #1 on: June 06, 2005, 12:54:04 AM »
Beware! The electricity company does not like to have power in the lines when linesmen work on them during outages and the men can then get electrocuted.


dom

 

« Last Edit: June 06, 2005, 12:54:04 AM by (unknown) »

georgeodjungle

  • Full Member
  • ***
  • Posts: 193
Re: one side one 240v inverter
« Reply #2 on: June 06, 2005, 12:56:57 AM »
there getting cut off.
« Last Edit: June 06, 2005, 12:56:57 AM by (unknown) »

drdongle

  • Hero Member
  • *****
  • Posts: 552
Re: one side one 240v inverter
« Reply #3 on: June 06, 2005, 05:20:48 AM »
If your getting rid of the grid, then disconnect the 3 main feed lines to the panel, and hook up the transformers secondary to the same connections.

If the inverters output is 240 and has no center tap for ground then yes you will need the transformer. The center tap on the secondary goes to panel ground.
« Last Edit: June 06, 2005, 05:20:48 AM by (unknown) »

nothing to lose

  • Hero Member
  • *****
  • Posts: 1538
Re: one side one 240v inverter
« Reply #4 on: June 08, 2005, 08:14:25 PM »
Not sure if this is what your asking,


I called Aims about the 240V inverters and was told they are for 240V, (220V).

Anyway you can't just split the legs like the grid and have 2 120V legs for normal stuff and the 220/240 for wells or dryers.  I was thinking about doing just that since I need 220V for my deepwell, 120v for everything else.


Not sure what I will do now myself, probably buy just a 220/240 inverter for the well only. Maybe wire a switch to it so the inverter is off untill water presure drops to 32PSI, turn on the inverter at that so it's ready, then the well set to turn on pump at 30PSI. Just so the inverter does not have to turn on under load of a dead motor.


Or I may just use a 220V generator and pump 200gals to an above ground tank then a 12Vdc pump from that or 110Vac pump on the normal inverter.


Transformers have losses and kinda expensive to get the high amp ones too.

« Last Edit: June 08, 2005, 08:14:25 PM by (unknown) »

georgeodjungle

  • Full Member
  • ***
  • Posts: 193
Re: one side one 240v inverter
« Reply #5 on: June 08, 2005, 10:54:51 PM »
ya ya i called to the cycles arn't 1/3 off each leg.

& they said "should balanced"

inverters are getting soooo cheap any ways...

p.s.

lots of smart people here > me
« Last Edit: June 08, 2005, 10:54:51 PM by (unknown) »