Attachments: spinner.JPG
spinner.JPG
Attachments: aandrijving.JPG
aandrijving.JPG
Here is why I needed to overhaul the Azimuth drive to begin with.
Need to revers engineer the circuit, easy enough to repair as just the rectifier module that blew but over all circuit is functional still.
(Attachment Link)
(Attachment Link)
(Attachment Link)
Now I will stop rambling now again for a while as I am still not even sure if this will even get out thereIt absolutely will, your posts increased in quality by several orders of magnitude, I am very glad to see that once you're calm and collected you're not rambling all the time and posting 7 times in a row, you're actually writing properly with some good points! Carry on like this
Attachments: main axle.JPG
main axle.JPG
Reminds me of the satellite television dish my parents had when I was young. It used pivots to tilt back and forth. The pivoting apparatus bore its weight on an arc shaped bar. As you rotated the dish horizontally there were wheels that rested against the bar. The bar sat on the horizontal pivot before the dish tilt machinism and could be adjusted about to any direction before keybolts held it tight against the main horizontal pivot. Until wind got in the low 50s the big dish could hold a tight signal.
Attachments: nacelle.JPG
nacelle.JPG
Do image system work now ?Yes, been a while
That's a facebook link and they got temporary signatures to show up, since Meta don't want us to use 1mb of their bandwidth and can't afford servers the image signature is scrambled every so often so people can't hotlink images off there.
@topspeed please put the actual images and don't hotlink off facebook image links, as it will only work for a couple of hours and then break itself, sadly not something I can do anything aboutYou can rest assured that if you upload the images on our forum they won't go away instead (unless the server and the backups implode but we don't talk about that
).
Attachments: statief.JPG
statief.JPG
Attachments: 18 rpm. 4 V.JPG
18 rpm. 4 V.JPG
Thanks for this wonderful piece of information. I been reading all your post for years.
Wondering the dimensions of your Heatsink or where to buy .
Now working on a triac based 3 stages Charging system and Transfer system.
Thanks in advance
As for the turbines, I prefer the VAWT to the HAWT because I find the slower rotational speed to be less intrusive if it's within sight of the house.
I am hoping to get mine flying this summer and see how she performs. At that time I would be happy to tell you my experience and things I would change or do different right away.
These guys are right, if you want a vawt, plan on it being bigger then a hawt. I thought I could squeeze my stator down to 14in and ended up a full 2in above that. It may not sound like much, but that pushes my mag plates out to 17in min 18 might be better, depending on thickness of steel. When you start adding inches to big chunks off spinning steel, you need to think about that, if for no other reason, weight on bearings and balancing. So a vawt can get bigger on you in a hurry.
Friends,
This is just me being miserable.
Let me find the most correct words to say what need to be said. And even now I am sure I will screw this up.
In essence.
I think this is the best place to share knowledge.
In practice:
I get my feathers ruffled at times as there are respected players here that know soo much more than I ever will yet leave me hanging.
Now that introduces my pride mechanism.
I do not care about being wrong at times. that does not influence my pride.
All I'd lie to make knows is that I care about this forum and that I am willing to stick my neck out to make it thrive again.
With no strings attached other than that the one holding the strings is one I feel confident in.
Now I will go into hibernation here. As I do not wish to fuffle feathers just for the fuffle.
We will meet again in the future and I will still love you.
Remember in where I had in mind this meeting in person? In where I will shake your hand and give this nod of respect?
kind regards
I posted this showing the difficulty with running a VAWT.for what purpose? this is a dead thread that OP made all of 1 or 2 posts on.
Don't know the size of your support mast for the panels but if you put a flat plate on your bottom tube one of these would last many years. Already weather sealed... I have used the next size down(2" mast) to support really heavy antenna loads...
https://www.dxengineering.com/parts/dxe-tb400
All ways good to have options, I need to do a total remake of the top half, I was going to use a vehicle hub was my idea
Don't know the size of your support mast for the panels but if you put a flat plate on your bottom tube one of these would last many years. Already weather sealed... I have used the next size down(2" mast) to support really heavy antenna loads...
https://www.dxengineering.com/parts/dxe-tb400
Attachments: IMG_20240427_124050.jpg
IMG_20240427_124050.jpg IMG_20240427_124057.jpg
IMG_20240427_124057.jpg IMG_20240427_124118.jpg
IMG_20240427_124118.jpg IMG_20240427_140405.jpg
IMG_20240427_140405.jpg IMG_20240427_181919.jpg
IMG_20240427_181919.jpg IMG_20240427_181928.jpg
IMG_20240427_181928.jpg IMG_20240427_181937.jpg
IMG_20240427_181937.jpg
Attachments: IMG_20240427_111655.jpg
IMG_20240427_111655.jpg IMG_20240427_111714.jpg
IMG_20240427_111714.jpg IMG_20240427_111736.jpg
IMG_20240427_111736.jpg IMG_20240427_111748.jpg
IMG_20240427_111748.jpg IMG_20240427_121528.jpg
IMG_20240427_121528.jpg IMG_20240427_121542.jpg
IMG_20240427_121542.jpg