Subject / Started by  |
Replies / Views | Last post | ||
|---|---|---|---|---|
| 0 Members and 42 Guests are viewing this board. | ||||
|
|
Smid-gen mini mite
Started by windstuffnow |
9 Replies
1850 Views |
September 02, 2008, 09:38:33 AMby PHinker |
|
|
|
Coil winding base...
Started by windstuffnow |
10 Replies
2410 Views |
April 16, 2007, 10:07:07 AM by Devo |
|
|
Lenz 2.4
Started by windstuffnow |
26 Replies
13443 Views |
October 19, 2006, 09:30:10 PM by motoman465 |
|
|
Mini 200
Started by windstuffnow |
17 Replies
2744 Views |
April 18, 2007, 07:28:52 PM by Spdlmt150 |
|
|
|
Hyper-mile-ing
Started by windstuffnow |
28 Replies
6251 Views |
July 06, 2008, 07:32:10 PM by tecker |
|
|
|
Wing flying upwind mpg
Started by windstuffnow |
10 Replies
2388 Views |
December 18, 2005, 03:23:36 AM by nothing to lose |
|
|
|
Predicting Turbine/alternator output
Started by windstuffnow |
2 Replies
955 Views |
October 13, 2005, 02:32:33 PM by windstuffnow |
|
|
|
Lenz2 pushing over 450 watts
Started by windstuffnow « 1 2 » |
40 Replies
14437 Views |
July 08, 2006, 05:46:09 PM by ZooT |
|
|
|
3 Replies
1175 Views |
October 14, 2003, 09:40:14 PM by windstuffnow |
|
|
|
|
4 Replies
1212 Views |
March 11, 2009, 06:56:09 PM by windstuffnow |
|
|
|
|
Lenz2 wind tunnel tests are done
Started by windstuffnow « 1 2 » |
38 Replies
25087 Views |
August 20, 2019, 05:55:07 PM by JW |
|
|
|
miniLenz2 with PCB stator
Started by windstuffnow |
14 Replies
12300 Views |
September 06, 2006, 02:55:38 PM by richhagen |
|
|
|
Stirling failure #2
Started by windstuffnow |
7 Replies
1066 Views |
March 20, 2007, 09:38:20 PM by veewee77 |
|
|
|
Lenz2 Water pump
Started by windstuffnow |
5 Replies
1580 Views |
November 26, 2005, 09:36:18 PM by windstuffnow |
|
|
|
Low Temp stirling
Started by windstuffnow |
16 Replies
2853 Views |
November 20, 2006, 06:55:14 AM by craig110 |
|
|
|
28 Replies
13420 Views |
October 15, 2005, 11:53:14 AM by hvirtane |
|
|
|
|
Radial playtime..
Started by windstuffnow |
22 Replies
2840 Views |
April 27, 2007, 12:33:29 AM by Flux |
|
|
|
Lenz turbine tests continue...
Started by windstuffnow |
15 Replies
6183 Views |
August 18, 2005, 11:30:41 AM by windstuffnow |
|
|
|
Lenz Turbine update...
Started by windstuffnow |
15 Replies
3172 Views |
August 22, 2005, 07:28:01 AM by electrondady1 |
|
|
|
Radial completed
Started by windstuffnow |
18 Replies
2005 Views |
April 30, 2007, 02:12:36 PM by windstuffnow |
|
|
|
Off topic - New Virus warning !!!
Started by windstuffnow |
12 Replies
2713 Views |
July 24, 2008, 01:57:14 AM by stephent |
|
|
|
Lenz turbine outside...
Started by windstuffnow |
8 Replies
1463 Views |
August 22, 2005, 09:51:18 PM by nvmike |
|
|
|
Making hot water with cavitations...
Started by windstuffnow « 1 2 » |
39 Replies
70246 Views |
June 02, 2012, 09:39:08 AM by OperaHouse |
|
|
|
CNC plasma cutter up and running...
Started by windstuffnow |
12 Replies
2305 Views |
March 12, 2007, 07:32:07 PM by tecker |
|
|
|
21 Replies
2966 Views |
October 28, 2005, 09:00:38 AM by SparWeb |
|
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll